- Does drip edge go over or under ice and water?
- Does drip edge go around entire roof?
- How much should shingles overhang drip edge?
- Should rain gutters be installed under drip edge?
- Do I need a drip edge on rake edge?
- Is drip edge needed on gable ends?
- Do you need to replace drip edge when replacing roof?
- Can you put drip edge on after shingles?
- How much does drip edge cost?
- What is a rake edge?
- Should drip edge be tight to fascia?
- Should you use drip edge touch fascia?
- What color drip edge should I use?
- Does drip edge go on rakes?
- What is the bottom edge of a roof called?
- What is a drip edge on a roof?
- What nails do you use for drip edge?
Does drip edge go over or under ice and water?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.
This lets any water that gets on the roof run down the underlayment and over the drip edge..
Does drip edge go around entire roof?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
How much should shingles overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Should rain gutters be installed under drip edge?
Your gutter needs to be a few inches under the edge of your roof. … Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.
Do I need a drip edge on rake edge?
It’s important to understand that drip edge installation is different for eaves and rakes. After your roof deck has been prepared, and before you install underlayment, you need to install drip edges at the eaves. You install drip edges on the rakes after you install the underlayment.
Is drip edge needed on gable ends?
What’s a drip edge? A drip edge is a piece of roofing trim. The drip edge supports overhanging shingles at the ends of a roof, providing structure to the overhang and directing water to the gutters and away from the fascia of the roof. … Drip edges can also be installed on the gable ends of a roof.
Do you need to replace drip edge when replacing roof?
Drip Edge Flashing Drip edge comes in 10-foot strips and attaches to the roof deck before the roofing felt goes on. Unless the old drip edge is in like-new condition, replace it.
Can you put drip edge on after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
How much does drip edge cost?
Drip Edges: $1-$2 per linear foot installed. Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters. Other Damage – Have a professional inspect your eaves for damage before repairing fascia and soffits.
What is a rake edge?
Simply put, a roof rake edge is installed to cover the top edge of the siding where it meets the roof. You can think of it as a type of awning that is designed to allow water to flow off the roof and down onto the ground below, instead of down the side of your home.
Should drip edge be tight to fascia?
Nail thefurring strip to the fascia board near the fascia top – tight under any extending of roof decking (usually absent); the Drip edge will be installed 1/8″ proud of (away or out from) the furring strip in best practice or may be installed tight against the furring strip (reduces the life of the furring strip by …
Should you use drip edge touch fascia?
The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.
What color drip edge should I use?
If your home’s trim and fascia are white, it is recommended you select a white drip edge for seamless blending of elements throughout. If your home has more pops of brown, similar to the home displayed in the photo to the right, you may want to choose a brown drip edge.
Does drip edge go on rakes?
Either style of drip edge is suitable for eaves or rake use. I generally choose the extended-style drip edge along eaves edges, so water rolling off the edge of the shingles will tend to drip away from the fascia and into a gutter. And to keep things simple, I use the same drip edge along rake edges.
What is the bottom edge of a roof called?
eavesThe eaves are the edges of the roof which overhang the face of a wall and, normally, project beyond the side of a building. The eaves form an overhang to throw water clear of the walls and may be highly decorated as part of an architectural style, such as the Chinese dougong bracket systems.
What is a drip edge on a roof?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.
What nails do you use for drip edge?
The drip edge is nailed in place using 1-1/2 galvanized roofing nails. A felt-tip marker works great for marking cuts. And, again, prying open the end with a small flat bar allows the pieces to overlap cleanly.