- How far should gutters extend from house?
- Can you install drip edge on existing roof?
- What goes first drip edge or felt?
- Should there be a gap between gutter and fascia?
- What is the difference between drip edge and rake edge?
- How do I extend the drip edge on my gutters?
- Does drip edge go over or under underlayment?
- Which is better drip edge or gutter apron?
- How far should gutters be from house?
- What is drip edge?
- Does drip edge go around entire roof?
- Should drip edge be tight to fascia?
- Why is water dripping between gutter and fascia?
- What does a gutter apron look like?
- How far down should gutters be from shingles?
- Can you install gutter apron over drip edge?
- How much should shingles overhang drip edge?
- What is proper gutter pitch?
How far should gutters extend from house?
The experts tell us 3 feet is sufficient.
We think that is a minimum distance.
Twenty feet is probably better.
A lot depends on the soil around your house..
Can you install drip edge on existing roof?
What if you need to replace the drip edge on an existing roof or install a drip edge on an existing roof for the first time? It can be done; here’s how: Step One : Gently lift up the shingles on the edge of the roof and locate the nails holding the existing drip edge onto the roof.
What goes first drip edge or felt?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Should there be a gap between gutter and fascia?
Gap is not needed. Remove the wood blocks and install same size 4 inch gutter, as gap is too small to make difference.
What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.
How do I extend the drip edge on my gutters?
If the gutter is mounted too far below the drip-edge, or if the kickout doesn’t extend far enough over the gutter, a retrofit solution would be to slip a strip of metal or rigid plastic flashing under the vertical fascia leg of the drip-edge and let the bottom edge of the strip overlap the back edge of the gutter.
Does drip edge go over or under underlayment?
5 Drip Edge says, “Underlayment shall be installed over the drip edge along eaves … .” Because the ice-barrier membrane in this situation is taking the place of the underlayment along the eaves edge, it should be installed over the drip edge according to the code.
Which is better drip edge or gutter apron?
Gutter aprons take on an additional role by hanging down an inch or so into the back of the gutter to prevent water from dripping or splashing behind the gutter. While a drip edge is about 2 1/2 inches wide on both sides of the fold, a gutter apron will usually measure 4 inches or more above and below the fold.
How far should gutters be from house?
A good rule of thumb: One downspout should not drain more than 35 feet of gutter. The gutters must be clean to prevent clogging. The downspouts need to be extended away from the home a minimum of four feet, with six feet being preferred.
What is drip edge?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.
Does drip edge go around entire roof?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Should drip edge be tight to fascia?
Nail thefurring strip to the fascia board near the fascia top – tight under any extending of roof decking (usually absent); the Drip edge will be installed 1/8″ proud of (away or out from) the furring strip in best practice or may be installed tight against the furring strip (reduces the life of the furring strip by …
Why is water dripping between gutter and fascia?
When the roof shingles do not extend past the metal drip edge the water will suck back on the metal drip edge ( this is called capillary action) and run behind your gutters. NOTE: Capillary Action is a water activity in which water adheres to a surface and follow the surface around.
What does a gutter apron look like?
A gutter apron is an L shaped metal and a drip edge is often more like a T shaped metal. Drip edge could work, but the lip is often too short and the shingles often not extended far enough past the fascia due to the T shape, to use the drip edge.
How far down should gutters be from shingles?
Shingle installation can impact gutter performance. Companies like GAF have shingle installation guides, usually stating that the shingles should extend no more than 1/2 to 3/4 inch beyond the drip edge. In many markets, drip edges aren’t code and roofers install shingles deep into the gutters.
Can you install gutter apron over drip edge?
A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter. … If there’s a drip edge installed where the fascia meets your shingles and the gutter is hung below the drip edge, get some roll flashing and tuck it up under the drip edge and over the top of the gutter.
How much should shingles overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
What is proper gutter pitch?
Gutters need to be pitched toward the downspouts for the water to flow properly. You want at least a quarter inch of slope for every 10 feet.